3 Axis Nema23 Stepper Motor 76mm CNC Controller Kit TB6600 Driver USB MACH3

Description: Package include: 3 × Nema23 Stepper Motor 57mm3 × TB6600 Stepper Motor Driver1 × Mach3 USB CNC Control Card+USB Cable1 × DC Switching Power Supply Nema23 Stepper Motor 270Oz-inMotor Type: Hybrid StepperPhase: 2 phaseStep Angle: 1.8 degree±5%Voltage: 4.8VHolding Torque: 180N.cm(270oz-in)Detent Torque: 6N.cm MaxRotor inertia: 440g.cm²Phase Resistance: 1ohmsInsultaion Class: BInductance: 3.5mH+/-20%(1KHz)TB6600 Stepper Motor Driver FeaturesOriginal brand new stepper motor driver chip8-speed current control7 kinds of subdivision adjustableInterface uses high-speed optical couplingAutomatic half flow reduces calorific valueLarge area heat sink is not afraid of constant high temperature environmentStrong anti-high frequency interferenceInput voltage anti-reverse protectionOverheat and overcurrent short circuit protectionThrough the 3-digit dialing code, you can choose 7-step subdivision control (1, 2 / A, 2 / B, 4, 8, 16, 32), 8-step current control (0.5A, 1.0 A, 1.5A, 2.0A, 2.5A, 3.0A).Mach3 USB Motion Control Board 4-axisMaximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor.Need use external 24V DC power supply to isolate USB and external port, and to make the system more stable.4 general-purpose inputs, you can connect the limit switch, estop switch, probe switch, back to zero and other device.4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps and other device.350W 24V DC Switching Power SupplyDC output: 24V 0-14.5AInlet stability: ±0.5%Load stability: ±0.5%DC voltage of Adjustable range: ±10%AC input voltage range: 115VAC/6.5A/50HZ----230VAC/3.4A/60HZ; Selected by switchOverload protection: 105%-135% cut off the output, automatic recoveryOver-voltage Protection: 115%-150% shut down O/P voltage, re-power on to recoverSetup/rise/hold-up time: 200ms、50ms、20ms/230VAC at full loadWithstand voltage: I/P-O/P: 1.5KvAC; I/P-FG: 1.5KvAC; O/P-FG: 1.5KvAC; 1minuteIsolation resistance: I/P-O/P、 I/P-FG、O/P-FG: 500VDC/100MΩHow to connect the Tb6600 driver ( or Stepper Motor) to CNC Motion Control Card?It should be noted that the wiring diagram of the 4-axis motion control card above is for reference only, then if you connect this control card and the TB6600 driver, such as connect to X-axis motor driver, then:Driver's "Pul+" connects to control card's XP+ pin ,Driver's "DIR+" connects to control card's XD+ pin ,Driver's " PUL- " pin and " DIR- " connection to USB Mach3 control card's " GND "Stepper motor's wrings ( 4 wires) :Connect stepper motor's RED wire to driver's A+ portConnect stepper motor's GREEN wire to driver's A- portConnect stepper motor's YELLOW wire to driver's B+ portConnect stepper motor's BLUE wire to driver's B- portPackage Include:3 × Nema23 Stepper Motor 57mm3 × TB6600 Stepper Motor Driver1 × Mach3 USB CNC Control Card+USB Cable1 × DC Switching Power SupplyTB6600 Stepper Motor DriverDescription of TB6600 Stepper Motor Driver Two-phaseElectrical parameters:Input voltage: DC9-42VInput current: 5A switching power is recommendedOutput current: 0.5-4.0AMaximum power consumption: 160WBreakdown: 1、 2 / A、 2 / B、4、 8、 16、 32Temperature Working temperature: -10-45°C; Storage temperature -40 °C-70°CInput and output description:PUL + : Pulse signal input + / PUL- : Pulse signal input -DIR + : Motor rotation direction control + / DIR- : Motor rotation direction control-EN + :Motor enable control + / EN- : Motor enable control-A + : Connect motor A + phase / A- : Connect the motor A- phaseB + : Connect the motor B + phase / B- : Connect the motor B-phaseVCC : Power supply positive terminal "+" / GND : Negative terminal "-"Note : DC9-42V: Do not exceed this range, otherwise it will not work properly or even damage the drive.4 Axis CNC USB Mach3 Controller Breakout Board1 status LED, indicate connection status on the board.Have 0-10V output port, you can use mach3 software to control the spindle motor speed.Support for 4-axis linkage, you can connect four stepper motor drives or servo drives.Support automatic probe toolSupport Emergency inputSupport for limit switch (It is recommended that the limit switch and emergency stop switch must be installed first and can be used normally.)Support for connecting electronic handwheelThis USB motion card does not need install any USB driver, Windows2000/XP/Windows7,can directly identify (Notice: Doesn't support Win8/win10/macOS system !!!) .If you are not familiar with the product and software features, make sure the machine's power switch on hand, you can quickly turn off the power.Recommends that users install the emergency stop button and make sure the button is functioning properly.The inverter interface (AVI +, AVI-) is isolated from the computer and the main control circuit, and has strong anti-interference ability.No interference signal will be introduced due to the introduction of external strong electrical equipment.This interface can output 0 ~ 10V analog signals, and can also be configured as 0 ~ 5V output.It is recommended that the limit switch and emergency stop switch must be installed first.If these protection switches are not installed, in an emergency, in addition to pressing the emergency stop to return (sometimes too late to press), and turning off the motor power (sometimes too late to turn off), the most convenient way to stop is to pull the USB cable !! As long as the USB cable is pulled, the machine will automatically stop! !! !!350W 24V DC Switching Power SupplyMultiple protection, Stable PerformanceShort circuit protection: when the output terminal is short-circuited, the power supply turns off the output, and the output voltage is 0V.Overcurrent protection: When the output current>115-150%, the output voltage turns off the output.Overload Protection: Power protection when load power＞105-135% of rated power.Temperature protection; the power supply is automatically protected at high temperatures.Double Ball Cooling Fan and Full Metal Housing DesignWith high speed and quite characteristics, it can ensure the temperature operation of the equipment and extend the service.The shell is made of aluminum alloy with high thermal conductivity system, which is reinforced and durable, and the design is more user-friendly.Input Voltage SwitchThe power supply has an input voltage 110V-220V switch button, which can adapt to different voltage requirement.Quadruple protection setting, high resistant to electricity, effectively reducing the impact of AC input.

Price: 99 USD

Location: New York

End Time: 2024-08-12T05:29:22.000Z

Shipping Cost: 25 USD