Description: Each of the bottle sizes are sold individually not as sets.QUIK-CURE™ 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn’t be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE™ is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE™ can be handled after 15 minutes. Full strength is reached in 1 hour. MID-CURE™ 15 min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE™ in most applications. MID-CURE™ is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength. SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE™ and FINISH-CURE™ to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full strength within 24 hours. FINISH-CURE™ 20 min. epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer and paint. FINISH-CURE™ can be sanded the easiest of all our epoxies and is excellent for the sheeting of foam core wings. Allow 8 hours for full curing. For best results, FINISH-CURE™ should be heated to a temperature above 85 degrees F or applying light weight fiberglass, lay cloth on balsa first, then brush on FINISH-CURE™. When fully saturated, go over the surface with a heat gun, and then squeegee off excess epoxy with a playing card from an old deck. Heat and remove excess several times for a light weight finish. If room temperature is below 70 degrees F use a heat gun on the surface several times for the next 2 hours. When dry, lightly sand, then fill surface with a low weight spakeling compound, scrapping off excess with a playing card. Sand to a smooth finish ready for primer. For heavy weight fiberglass, apply the epoxy before and after laying down the cloth. FINISH-CURE™ is best mixed in a disposable cup. FOAM-CURE™ is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it’s curing. To obtain a faster initial bond when bonding two pieces, FOAM-CURE™ can be applied to one piece and after the two are joined, they can then be pulled apart. After letting it air dry for about ten minutes, FOAM-CURE™ will act like a contact cement when the parts are rejoined, resulting in enough tack strength to allow the next steps of assembly. Full strength is reached in 10-12 hours.FOAM-CURE™ works with all foams, and will actually bond most other materials. It will bond wood and plastic to foam, and is a good canopy glue. FOAM-CURE™ does not, however, cure flexible enough to act as a hinge for aircraft control surfaces. Its limitations occur when bonding large areas of two non-porous materials. FOAM-CURE™ requires exposure to air for drying. If one tried to bond, for example, a half-dollar coin to glass, over 90% of the adhesive would never cure, since the solvent it contains would have no where to evaporate. A small amount of denatured alcohol can be mixed into the Foam-Cure to make it thinner.IC-2000™ is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. For model use, IC-2000™ is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages. Setup time is 20-40 seconds, which can be accelerated with INSTA-SET™. When cured, IC-2000™ is pliable enough to be carved with a hobby knife. IC-2000™ is the best adhesive for R/C car tires.IC-2000™ has found many uses in industrial applications, such as rubber to rubber bonding by Beechcraft, carbon composite bonding by Boeing, rubber door seals by Volkswagen, speaker and subwoofer assembly in the audio industry and many others that need the most durable, shock resistant fast bonding adhesive that is available. Plastic-Cure™ is a gap-filling formulation of CA that works best on plastics. It is packaged in a bottle with a brush built into its top, which in many cases is an easier way to apply the CA. As long as brush is put back into the bottle after use, the bristles of the brush will not harden. Care must be taken, however, not to introduce foreign material into the bottle. The brush should not be used, for example, to apply CA to wood that has been freshly sanded. Plastic-Cure will also bond wood, but its brush applicator at times will not be the best way to apply it. Plastic-Cure is superior for the application of false nails and wraps on fingernails, where its brush is the preferred method of application. Ultra-Cure™ is a very high performance clear cyanoacrylate that has a viscosity (thickness) in-between that of Insta-Cure Super Thin and Insta-Cure+ Gap Filling Medium. It is ideal for the mounting of rubber tires onto R/C car wheels. It is available in our 3/4 oz Pocket CA bottle and comes with one of our new #304 Extender Tips for the Pocket CA pin-in-cap top. ULTRA-CURE™ can be used in many other applications that require a slightly thicker thin CA and will bond virtually everything. It is not foam-safe, however. We are a family owned and operated business located in Prescott Valley, Arizona. We have been in business for 45 years and sell the highest quality merchandise available. Items will be shipped USPS. Items will take 2-5 days for delivery. Items will ship within 24 hours of being purchased. We offer a 14-day Money Back Guarantee. (All items Returned AS IS) We combine shipping on most purchases. Buyer Pays Return Shipping. Thank You For Your Business
Price: 5.99 USD
Location: Prescott Valley, Arizona
End Time: 2024-08-12T22:35:46.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Finish: Clear
Brand: BSI EPOXY
Type: Multi-Purpose Glue
Available Variations
Color: 201 Epoxy 5 min. 4.5oz.
Price: 14.96 USD
Available Quantity: 15
Quantity Sold: 13
Color: 202 Epoxy 5 min. 9oz.
Price: 20.96 USD
Available Quantity: 13
Quantity Sold: 11
Color: 203 Epoxy 15 min. 4.5oz.
Price: 14.96 USD
Available Quantity: 11
Quantity Sold: 9
Color: 204 Epoxy 15 min. 9oz.
Price: 20.96 USD
Available Quantity: 6
Quantity Sold: 3
Color: 205 Epoxy 30 min. 4.5oz.
Price: 14.96 USD
Available Quantity: 15
Quantity Sold: 13
Color: 206 Epoxy 30 min. 9oz.
Price: 20.96 USD
Available Quantity: 14
Quantity Sold: 13
Color: 209 Finish Cure 20 min. 4.5oz.
Price: 16.91 USD
Available Quantity: 4
Quantity Sold: 2
Color: 210 Finish Cure 20 min. 13oz.
Price: 35.96 USD
Available Quantity: 5
Quantity Sold: 3
Color: 141 Foam Cure 1oz.
Price: 6.85 USD
Available Quantity: 5
Quantity Sold: 3
Color: 142 Foam Cure 4 oz.
Price: 9.95 USD
Available Quantity: 6
Quantity Sold: 5
Color: 117 IC 2000 1/2 oz.
Price: 11.95 USD
Available Quantity: 8
Quantity Sold: 7
Color: 118 IC 2000 1 oz.
Price: 13.95 USD
Available Quantity: 11
Quantity Sold: 11
Color: 105 Plastic Cure 1/2 oz.
Price: 13.95 USD
Available Quantity: 6
Quantity Sold: 2
Color: 130 Tire Glue 3/4 oz.
Price: 10.75 USD
Available Quantity: 11
Quantity Sold: 7
Color: 301Extender Tips bag of 6
Price: 6.99 USD
Available Quantity: 6
Quantity Sold: 2
Color: 302 FineExtender Tips bag of 6
Price: 5.99 USD
Available Quantity: 5
Quantity Sold: 4
Color: 304 Pocket CA Extender Tips bag of 6
Price: 7.99 USD
Available Quantity: 3
Quantity Sold: 1
Color: 305 Tubing 2 Ft Bag
Price: 5.99 USD
Available Quantity: 2
Quantity Sold: 2
Color: 305 Tubing 2 Bags-2 Ft Bag
Price: 7.99 USD
Available Quantity: 1
Quantity Sold: 0
Color: 303 Extra Long Tips 6 Pc.
Price: 5.99 USD
Available Quantity: 2
Quantity Sold: 2
Color: 303 Extra Long Tips 12 Pc.
Price: 8.25 USD
Available Quantity: 3
Quantity Sold: 1
Color: 303 Extra Long Tips 24 Pc.
Price: 12.25 USD
Available Quantity: 1
Quantity Sold: 0
