Description: To select the right SPEEDi kit for your eBike:Check Product Options: Click on an option to view the hub image it supports.Match Your Hub and Bike: Compare your eBike?s hub with the images and tested eBike list provided in the description. Verify that your eBike matches the tested models listed.Need Help? If your hub or model isn?t listed, contact us with photos of Your rear hub, and we?ll guide you to the right kit The SPEEDi is an e-bike speed limit increaser. Designed, tested and manufactered in New Zealand, our SPEEDi uses a mechanical planetary gear system to increase your standard e-bike speed limit by 1.5.Please note that the SPEEDi is very specific to the chosen Bike, Hub and Disc setup. Please don't assume that because your bike is similar it will fit, as it likely won't. If you're not 100% sure, please contact us. This list is illustrative and not exhaustive. Below are known Scott e-bikes with corresponding hubs. Note: some Scott bikes are Hub + Bike model specific only options, so choose accordingly. Shimano MT400/MT410 CL hubFound in models:2020- 2021 Scott Genius2022 Scott Patron2022 Scott Ransom CL-148S hub + 2020-2021 Genius/Strike CL-148S hub + 2023 Scott Solace Syncros Revelstoke-E 1.5 CL + 2023 Scott Solace Syncros Revelstoke-E 1.5 CL + 2022 Scott Patron Zipp ZR1 hub + 2023 Scott Solace eRide 10 My unit is making a lot of noise. What should I do?To make it silent, take your time to read the installation instructions thoroughly as it has simply been pushed on too hard, causing too much friction between the cover and backing plate, we aim for a very slight gap between the components. Please note that it's normal to have a little bit of noise in the beginning while things bed in. This will go away after the first ride. Do not add any lubricant to lessen the noise. Lubricant will just gunk it up and attract contaminants.Do I need to add lubricant?We highly recommend not applying any form of lubricant on the unit, as the Acetal plastic is self lubricating, any lubricant will just gunk it up and attract contaminants.What do I need to do for long term care?The SPEEDi is made from Acetal plastic which is self lubricating, which means you don't need to add any lubricants (see above)Generally, there is no need to clean the SPEEDi. When installed correctly, the tight seal tolerances keep out most dirt and water - there may be some very fine particles that get in, but these shouldn't affect performance. There's no harm in opening it up once in a while to make sure it's looking good and clean it up, but it's not required.How to install Speedi for 6 bolt hubs?1. Remove the rear wheel.2. Clean the disc and end cap from all contamination.3. Remove the 6x disc bolts and magnet and set aside (somewhere safe).4. Place the disc onto the hub, then the Backing Plate on to the disc, then install 6x new Bolts to 5-6nm with Blue Threadlocker.(if your bike uses the Shimano black aluminium disc with 3x bolt anti-rotate shims, re-install these shims) IMPORTANT Make sure the heads of the bolts are BELOW the surface of the Backing Plate.5. Place the Magnet inside the Backing Plate and engage the teeth.6. Take your time during the final install, make sure everything is very clean for a long and prosperous life.7. For silent operation we aim to leave a .1mm gap between the Cover and the Backing Plate:7.1 Gently press the Cover onto the end cap with thumb pressure only, rotating as you go. This is supposed to be a very tight fit, so will take some pressure to get it on. WARNING! Press as close to the center as possible, do not put ANY pressure on the outer edge of the cover OR hit it with any tool, or it will break.7.2 HOT TIP - soak the Cover in hot water (not boiling) for 10 seconds, this makes the plastic slightly larger and more malleable.7.3 As the Cover engages the last 2mm, the teeth need to line up so you will need to rotate the Cover slightly to allow easy engagement. Using a socket that fits over the axle and gently pressing it with your palm is a good way to install easily, be careful not to press it on too hard though, as this will likely make it noisy.7.4 Continue to press the Cover closer until you see a very small gap of around .1mm between the Backing Plate and Cover. You can test how close it is by pushing the outer edge of the Cover toward the Backing Plate and seeing how much it moves.8. Rotate the axle to make sure it spins freely and perfectly straight. Try pressing the hub end cap toward the hub and rotating, listening for excessive noise, as the wheel bearings may have play in them that can affect the offset when the axle is done up tight.9. There may be some slight plastic on plastic noise as the sealing faces gently touch each other, make sure this noise is not excessive, if anything sounds or feels off, pry it off completely (see uninstallation below) and re-install.10. Install the wheel gently into the frame, careful not to impact the unit or sensor.11. When tightening the axle - make sure there is always a slight gap between the unit and the sensor/frame at all times.12. Please note that for the first 5 minutes of use the unit may make some groovy noise, this is normal and will run smooth and silently after its initial bedding in. If it continues to make excess noise, try uninstalling (see below) and reinstalling following Step 7 closely.Installation Video How to install Speedi for Centerlock Hubs?1. Remove the rear wheel.2. Clean the disc and end cap from all contamination.3. Remove the stock Centerlock nut and magnet, set aside (somewhere safe)4. The Centerlock unit comes assembled. Disassemble the unit by pressing the Centerlock nut on the side with the 'NLS' on it. It will push out of the Backing plate.5. Install the new Centerlock nut with the stock stainless washer, grease the threads sparingly and tighten to 40nm with a good quality Bottom Bracket tool. Be very careful not to slip or damage the outer surface of the nut as this is what the Backing Plate mounts to, if this does get damaged, you will need to gently file off any burrs before installing the Backing Plate.6.Gently press the Backing Plate on to the Centerlock nut, start by lining up the 16 notches on the outer diameter, then with one edge fully on - work your way around the inside pushing with your thumbs, one notch at a time, until it clicks on. You know it is on correctly when the Centerlock nut face and Backing Plate are completely flush.7. Place the Magnet inside ring gear and engage teeth.8.Take your time during the final install, make sure everything is very clean for a long and prosperous life.9. For silent operation we aim to leave a .1mm gap between the Cover and the Backing Plate.9.1 Gently press Cover onto the end cap with thumb pressure only, rotating as you go. This is supposed to be a very tight fit, so will take some pressure to get it on. WARNING! Press as close to the center as possible, do not put ANY pressure on the outer edge of the cover OR hit it with any tool, or it will break.9.2 HOT TIP - soak the Cover in hot water (not boiling) for 10 seconds, this makes the plastic slightly larger and more malleable.9.3 As the Cover engages the last 2mm, the teeth need to line up so you will need to rotate the Cover slightly to allow easy engagement. Using a socket that fits over the axle and gently pressing it with your palm is a good way to install easily, be careful not to press it on too hard though, as this will likely make it noisy.9.4 Continue to press the Cover closer until you see a very small gap of around .1mm between the Backing Plate and Cover. You can test how close it is by pushing the outer edge of the Cover toward the Backing Plate and seeing how much it moves.10. Rotate the axle to make sure it spins freely and perfectly straight. Try pressing the hub end cap toward the hub and rotating, listening for excessive noise, as the wheel bearings may have play in them that can affect the offset when the axle is done up tight.11. There may be some slight plastic on plastic noise as the sealing faces gently touch each other, make sure this noise is not excessive, if anything sounds or feels off, pry it off completely (see uninstallation below) and re-install.12. Install the wheel gently into the frame, careful not to impact the unit or sensor.13. When tightening the axle - make sure there is always a slight gap between the unit and the sensor/frame at all times.14. Please note that for the first 5 minutes of use the unit may make some groovy noise, this is normal and will run smooth and silently after its initial bedding in. If it continues to make excess noise, try uninstalling (see below) and reinstalling following Step 9 closely.Installation VideoImportant legal notePlease note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use of NLS products. Electric bikes equipped with NLS products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with NLS products can be used exclusively on private property and entirely at one?s own risk. The use of NLS products may void the warranty of your ebike.We strongly recommend using other safety features and protective gear to prevent injuries in higher speeds.NLS products are thoroughly tested and we stand by their quality - NLS provides 1 year warranty to all their products.
Price: 129 USD
Location: Kaunas
End Time: 2025-02-07T07:48:33.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money back or replacement (buyer's choice)
Return policy details:
Manufacturer Warranty: 1 Year
Number of Items: 1
MPN: Scott
Compatible Model: Various Scott e-Bikes with specific hubs
Compatible Bike Type: Electric Bike
Item Width: 30mm
Unit Type: Unit
Item Length: 50mm
Item Height: 6mm
Country/Region of Manufacture: New Zealand
Material: Composite
Colour: Black
Model: Speedi
Item Weight: 200g
Compatible Brand: For SCOTT
Unit Quantity: 1
Brand: SPEEDi
Color: Black
Set Includes: Bottom Bracket
Part Type: Tuning kit
Available Variations
Color: Shimano MT400/MT410 CL
Price: 129 USD
Available Quantity: 14
Quantity Sold: 0
Color: CL-148S hub + 2020-2021 Genius/Strike
Price: 129 USD
Available Quantity: 14
Quantity Sold: 0
Color: CL-148S hub + 2023 Scott Solace
Price: 129 USD
Available Quantity: 2
Quantity Sold: 0
Color: Syncros Revelstoke-E 1.5 CL + 2023 Scott Solace
Price: 129 USD
Available Quantity: 2
Quantity Sold: 0
Color: Syncros Revelstoke-E 1.5 CL + 2022 Scott Patron
Price: 129 USD
Available Quantity: 14
Quantity Sold: 0
Color: Zipp ZR1 hub + 2023 Scott Solace eRide 10
Price: 129 USD
Available Quantity: 1
Quantity Sold: 0
